http://www.cb-adhesive.com
Home> Industry Information> hot melt bookbinding glue

hot melt bookbinding glue

August 22, 2019

Cover tape

For the cover, adhesive tape is allowed throughout the entire length of the head. If the spine length is 11 1/2 inches (292.1 mm), then the length of the book cover is at least 113/4 inch (298.4 mm). Position the center position, which exceeds 1/8 inch (3.2 mm) at the head and foot, respectively. When the cover and book size are the same, the perfect binding operator must use a mechanical timing scraper when gluing the book and the side to prevent the glue from running out on the working wheel during operation, which will reduce the production speed and quality.

Adhesive cover design instructions

As far as possible, the silk cocoon is parallel to the direction of the spine;

To obtain high quality products, make book indents on a die cutter;

For thin books, avoid using thick covers (≥10pt);

Inside the front seal ink, glazing and UV coating should not enter the indentation of the book, the distance from the spine is greater than 1/16 inch (1.6mm).

Keep the book ink and layers away from the edges of the spine;

The cover sheet that is required to be transported has a printer port and a side guide mark.

Book preparation

The spine and signature heads are perforated so that the air in the pages is released. Then, the platen sticks the books together and presses them as tightly as possible. This method is very important for stacking books. Do not place stickers in the opposite direction at the same time when you are feeding, but place them in the same direction. Using oppositely curved molds (eg, concave and convex), work together on a book. A good wireless Glue Binding requires that the book be clamped together before it is glued with the cover, and then pressed through the grinding wheel and tire. If the clip is not tight, glue may spread between the signatures. Once the book is spread and does not match the habit, the job has problems.

Book inserts

Inserts fold, half-fold, roll-fold, etc. The requirement for cutting blanks is 1/8 inch (3.2 mm), so the folding does not require gluing, and should be given a 1/8 inch reserve , so this kind of folding cannot be aligned with the entire page. If the reserve is too small, the operation ability of the binder may be limited, for example, it may be difficult to perform cross-page positioning. Similarly, for the inner back cover of the bookbinding booklet, a space of 1/8 inch is also required. The best way is to confirm with the binder to ensure that all the booklets are Folds have the correct size.

Die cutting

The use of die-cutting methods can be used to determine the exact size of the book.

Auxiliary equipment

The Foldout MylarTM device produced by DuPont Company has the function of tagging between book pages, but the use of such equipment will increase the cost of the wireless glue-binding product. This staggered tag looks very interesting. This type of machine will only put logos between the book stickers, and will not print the logos on the front cover and the single-page pages. Try to use a variety of post-printing functions (such as die-cutting, foil-foil, marking, and compression packaging) on the staple job. This way, the work process will be more coordinated and easier to control.

Compressed packaging

Don't be shrewd and wasteful. You can use a compressed pack of books to prevent confusion. If it is a small number of jobs that require refined packaging, it may be safest to compress the packaging to a minimum.

Packing

Provide the binder with the correct number of bales for the job to avoid re-bundling the jobs. If the books are bundled loosely, it is easy to scratch, scratch or scratch the cover.

Arrange cross-page images and double arrangement

The arrangement of binding images for wireless bindering requires skill and science. In addition to the 1/8-inch (3.2 mm) book-stitching opening, precise layouts depend on the design and how the book is opened. In order to maximize operator flexibility, the page image is arranged 3/16 inches (4.8 mm) from the edge of the opening. Cross-page images should appear exactly at the opening. To achieve this effect, the reserved area should be shorter by 1/16 inch (1.6mm). If the book is thick or printed on thick paper, move the image outward, which is to set aside 1/32 inch (0.8 mm). If the books are thin, the reserved area for the reservations will be reduced. In general, the diagonal of the two pages should be close to the visible image boundary.

When cross-page images appear between pages, the accuracy of folding is also a big factor. At this time, if you want to choose a binding factory, all book-folding work must be done by them.

Double arrangement

To double the speed of production, binding of long, small books can use a twin-up, wireless glue book design. This relative arrangement is a commonly used method. Because many binders can't do double binding, we may need to specifically look for such binding equipment. For this unusual design, you can seek some help.

In general, the size of the mouthpiece cover is 1/8 inch (3.2mm) smaller than the cover size. Therefore, the book spine is not aligned. However, if you do double-adhesion, you can avoid this 1/8-inch difference. First, bind the pages together, then wrap the cover on the page and align the head and leg. This will give you the perfect glued product. Book pages flush with the cover

Other tips

Perforated signatures reduce wrinkles in the paper and improve the tightness between pages. Punching requires only a small gap. But it should be enough to let the air in the folder release, and it should not be too deep. Too deep will make the pages too loose.

If the glue is more secure, consider indenting the glue, so that the small serrations you create will get stuck on the book. The page factor is that the book spine of a grooved book sometimes requires a nail head effect, so the rubber edge will be thicker than the average book. The experienced wireless glue binding company adopts the latest glue binding technology for ordinary glue binding jobs. , can get a good glue binding effect.

Using cover heavyweight paper for text paper, it is difficult to get enough page tension. In this case, binding using the staple method will be better and stronger.

For eye-catching considerations, use adhesive tape binding. Tape binding can exhibit color, firmness, and unique effects.

When folding, changing the type of paper can create confusion because the thickness of the paper must be stable during this process to ensure proper functioning of the clip and electrosensitive device.

Some of the mistakes are costly and wasteful. For example, if books that are bound together are changed to saddle stitching, then in order not to waste these books, the spine must be cut in half, and the book be set on a horse.

The above is the hot melt bookbinding glue we have listed for you. You can submit the following form to obtain more industry information we provide for you.

You can visit our website or contact us, and we will provide the latest consultation and solutions

Share to:

Send Inquiry

Home> Industry Information> hot melt bookbinding glue
Communicate with Supplier?Supplier
zhaowenhua Mr. zhaowenhua
What can I do for you?
Contact Supplier